Table of Contents
How To Clean a Jet Ski After Salt Water Use.
Jet skis require a sizable financial outlay to buy. Therefore, in order to avoid any losses over the long term, you need to properly care for your investment by “taking care,” we refer to thorough jet ski maintenance. You must continually perform meticulous maintenance on a jet ski in order to keep your vehicle in top working order.
To thoroughly clean your Jet Ski, you can follow our five easy steps. Before we move on to the actual cleaning procedure, let’s first take a look at some of the tools you will need:
A garden hose is required for jet ski cleaning. Alternatively, you could use a pressure washer. If you are cleaning a really dirty jet ski then you will need a liquid cleaner.
Soap: You can either use regular car soap or specialized boat soap.
Rags: White cloths rather than a foam sponge should be used to apply soap to the jet ski and to dry it. They can get into awkward spaces that a sponge can’t. In addition to some microfiber rags, you need a lot of white, fluffy rags.
Long-handled scrub brushes are also necessary because they will make it easier for you to clean jet ski seats in particular. You’ll also need a wax spray to give your jet ski a nice finish.
Cleaning a Jet Ski
The first step in cleaning a jet ski is to give it a thorough hose-down. After that, thoroughly clean the entire jet ski, including the seats and the engine compartment, using a cleaner and water mixture. Finally, give it another hose rinse and completely dry the entire craft.
To prevent mold from growing on the inside of the cover, make sure it’s properly dry. On occasion, you might think about using some spray wax to make the hull shine.
Let’s drill down and examine each step in more detail.
1: Thoroughly rinse it.
Start by giving your jet ski a good, thorough rinse with a garden hose. Your jet ski’s footwells, which are generally covered in a thick layer of dirt, slime, and goo, will be the dirtiest part of the vehicle.
You can remove everything with a power washer but be cautious when using a power washer near the decals and soft spots as this could damage due to the powerful spray. You’ll need to repeat the process after your initial water spray to reach interior surfaces.
Open all the lids and storage spaces after removing the seats. Remove the drain plugs but avoid spraying water on the craft’s electrical components.
2: Wash with water and a jet ski cleaner.
This is the most crucial step in cleaning your jet ski. Apply the jet ski cleaner mixed with 50% water once your craft has been rinsed and is completely wet. Use a cleaner and water mixture to wash the jet ski. It can be used to coat just about anything, including the engine. Make sure to cover the footwells with additional layers. Use the cleaner only if your jet ski is extremely dirty and requires a lot of cleaning. Additionally, stay away from aluminum and oxidized white fiberglass, both of which can turn yellow. Rinse the jet ski cleaner off and then re-wet it. This time, get a bucket, add a few drops of car soap, and soak a white rag in it (5-gallon buckets work well). Divide your jet ski into four sections, and wash all the soap from each section before moving on to the next, same method as you would clean your car.
3. How Should a Jet Ski Engine Be Cleaned?
The engine of the jet ski needs to be cleaned, particularly if you used the ski in saltwater. With a damp sponge, you can easily clean a jet ski engine. Make sure your engine is completely cooled before doing anything else! It’s best if you use a sponge to first remove the water from the engine. After that, use a low-pressure hose to gently rinse both that and the bilge. Never clean a jet ski engine with a high-pressure washer! You can use Simple Green again if your engine or engine compartment is extremely dirty, or you can think about using a different, more specialized biodegradable motor degreaser for better cleaning. Many owners favor using a small amount of Gunk Engine Cleaner followed by brushing the engine. Finally, thoroughly clean it with a sponge. This solution is especially helpful if you own an older 2-stroke jet ski because the engine in these models tends to get quite dirty over time. Use some lubricant as a finishing touch to shield the rubber components, terminals, and hoses.
4. Jet Ski Seat Cleaning.
Given that you will be sitting in your seats the entire time you are out at sea, you should take extra care of them. How Should a Jet Ski Seat Be Cleaned? After rinsing a jet ski seat, you should spray some jet ski cleaner on it to clean it. Finally, thoroughly clean it with a scrub brush. Try using a Magic Eraser for a deeper clean.
5. Apply Dry-Wax.
Make sure your jet ski is completely dry before moving on to the waxing step. Using a spray wax will give it a flawless shine and protect it from weathering. Make sure to spray the wax when the air is cool and out of the sun. You won’t do any harm by giving it a couple of coats.
How Should a Jet Ski Cover Be Cleaned?
The best method for cleaning a jet ski cover is to lay it out on the driveway first. Next, thoroughly wet it with a hose, apply some Simple Green, and give it a good scrub. After finishing, give it another rinse before hanging it up to completely dry.
FAQs
What Cleaners Are Available for Jet Skis?
To clean a jet ski, you can use Simple Green or marine soap. You’ll also need a garden hose, a bucket, rags, a sponge, and possibly a scrub brush. You might want to use a vinegar/water solution to get rid of water stains.
How Should a Jet Ski Be Cleaned After Use?
If possible, as part of the after-ride maintenance, a jet ski should be cleaned. Connect a low-pressure hose to the flushing port, you should flush through the systems (cooling, exhaust) in addition to cleaning the entire hull and the interiors.
How often should I detail my jet ski?
A: It is generally recommended to detail your jet ski at least once a year, or more often if it is used frequently or in salt water.
What is the best way to wash my jet ski?
A: The best way to wash your jet ski is to rinse it with fresh water, using a hose to remove any salt water, sand, or other debris. Use mild soap and a soft sponge to wash the jet ski’s hull and deck. Rinse the jet ski again with fresh water, and use a soft cloth to dry it.
What is the best way to wax my jet ski?
A: The best way to wax your jet ski is to apply a coat of jet ski wax to the hull and deck. Buff the wax with a clean, soft cloth.
Summary
- Rinse the jet ski with fresh water, using a hose to remove any salt water, sand, or other debris.
- Use mild soap and a soft sponge to wash the jet ski’s hull and deck. Rinse the jet ski again with fresh water.
- Use a soft cloth to dry the jet ski.
- Apply a coat of jet ski wax to the hull and deck.
- Buff the wax with a clean, soft cloth.
- Inspect the jet ski’s engine and other mechanical parts. Make sure that all nuts and bolts are tight.
- Check the jet ski’s hull and deck for any cracks or other damage.
- If you do find any damage then have it repaired by a qualified jet ski mechanic.